Edge10 DAS200 User Manual

2 Bay SATA II to USB & eSATA Combo Storage Appliance DAS200 User’s Manual

1.7 PRODUCT CONTENTS The following parts are content. a DAS200 x 1. a Power Adapter x 1. a Power Cable x 1. a Tool-less Screw x 4. a Setup

2 INSTALLATION 2.1 INSTALLING HARD DISK DRIVE Please refer below procedure to complete the HDD installation. • Unfasten the Tool-less screws on t

• Twist the Tool-less screws shut to seat the drive securely. • Close the front door and the upper chassis cover, than fasten the Tool-less screws

2.3 POWER ON / OFF • Push the power switch to position “ I ” to power on. • Push the power switch to position “ O ” to power off.

3 CONFIGURATION 3.1 CONFIGURATION PREREQUISITES 3.1.1 SATA HOST CONNECTIONS This guide assumes that you have already attached the DAS200 to a host

3. The following message then appears: “Safe to Remove Hardware”. You can now safely disconnect the device from your computer. Note: If your host USB

3.5.2 eSATA HOST LED The DAS200 has one Green color eSATA Host LED. The table shows eSATA Host LED function and operation. DESCRIPTION GREEN LED eS

3.6.1 STANDARD (INDIVIDUAL) MODE IMPORTANT: Before reconfiguring a volume, back up your data and delete previously defined partitions. 1. Turn on the

3.6.2 COMBINE (BIG) MODE IMPORTANT: Before reconfiguring a volume, back up your data and delete previously defined partitions. 1. Turn on the power.

3.6.3 STRIPING (FAST) MODE IMPORTANT: Before reconfiguring a volume, back up your data and delete previously defined partitions. 1. Turn on the powe

Table of Contents 1 WELCOME ...

3.6.4 MIRRORING (SAFE) MODE IMPORTANT: Before reconfiguring a volume, back up your data and delete previously defined partitions. 1. Turn on the powe

Note: After you have pressed the Mode Change push-button, and than wait a while, the MIRRORING mode will start to rebuilding (depand on the capacity

4 PARTITIONING VOLUMES 4.1 PARTITION A VOLUME 4.1.1 WINDOWS SYSTEMS IMPORTANT: Before repartition a volume, back up your data and delete previous

Every disk should appear with the word “Basic”, a size value that shows the available storage capacity, and a status of “Online”. Instead of Basic, a

4. Click Next to start the Partition Wizard. 5. Select the Primary or Extended option and click Next. Ver. 071004 DAS200 User’s Manual 36

6. Specify the partition size. By default, the partition occupies the entire volume. Click Next. 7. Assign a drive letter or mount path and click N

8. Name and format the partition and click Next. 9. Review the file system settings and click Finish to create the logical partition. Ver. 071

10. Repeat steps 1 through 9 to partition any remaining disks. 4.1.2 MACINTOSH SYSTEMS IMPORTANT: Before reconfiguring a volume, back up your data

2. Select a configured disk and click the Partition tab. This procedure illustrates the COMBINE Storage Policy configuration, which concatenates the

8. Click Partition to acknowledge the warning. Disk Utility mounts the created partition and represents it with an icon on the desktop. The icon is

3.6.1 STANDARD (INDIVIDUAL) MODE ...29 3.6.2 COMB

5 FAQ If you need some help for troubleshooting, please check the frequently asked question below, it may help you problem solved quickly a Can not

1 WELCOME 1.1 INTRODUCTION Thank you for choosing DAS200 storage appliance. It is a low-cost, single-chip solution for digital home and small offi

a Please be noted the following product may run irregularly which are not under warranty.  Toshiba DynaBook, Satellite series (All K6 CPU models).

1.4 SPECIFICATIONS a Two 3.5-inch SATA hard disk drives to a standard B type USB or eSATA interface with door cover. a Power, Host, Alerm and two

node is detected by your host. Therefore, selecting STANDARD mode for any subordinate node is not recommended. In a STANDARD configuration, the DAS200

1.5.3 STRIPING (FAST) The STRIPING storage policy distributes access across all hard disks, also called FAST (equivalent to RAID 0). STRIPING present

BANC, although no mirroring will occur until a second hard disk drive is connected to Port 1. With only one hard disk drive connected, the MIRRORING